Current ICS® Pipe-Cutting 680ES PG Gas Power Cutter

2020 ICS® 680ES PG Gas Power Cutter Base

2020 ICS® 680ES PG Gas Power Cutter Base

Swipe to View More

  • Year 2020
  • Make ICS®
  • Model 680ES PG Gas Power Cutter
Shop ICS® Pre-Owned
Product Details Specifications Photos
2020 ICS® 680ES PG Gas Power Cutter Base

2020 ICS® 680ES PG Gas Power Cutter Base

  • Year 2020
  • Manufacturer ICS®
  • Model Name 680ES PG Gas Power Cutter
  • Trim Name Base
  • Generic Type (Primary) General
  • Engine Power 3.7 kW (5 hp) @ 9,500 rpm
  • Engine Torque 4.1 Nm (36.3 in-lbs) @ 6,500 rpm
  • Rated Engine Speed 11500 +/- 500 rpm (max) / 2,800 - 3,200 rpm (Idle)
  • Displacement 76.5 cc (4.7 cu-in)
  • Engine Type 2-stroke
  • Cooling Air Cooled
  • Starter Dust and water resistant
  • Ignition Special water resistant electronic ignition

2020 ICS® 680ES PG Gas Power Cutter

Built to provide a combination of performance and portability for cutting in-ground utility pipe, the 680ES-PG Gas Power Cutter with PowerGrit® chain will change the way you cut pipe.

The 680ES PG allows you to cut up to 10 in. deep into ductile iron, cast iron, PVC, HDPE, and Insituform lining, and is also designed to fit the full line of FORCE3® Series chains.

With a quick switch of the guide bar, chain, and drive sprocket, you can use this power cutter in masonry, stone, and even reinforced concrete.

The 680ES-PG may be the most cost-effective, versatile tool in your arsenal.

This product can expose you to chemicals, including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Features may include:

  • Polyester air filter designed specifically for wet cutting
  • Operates PowerGrit Pipe Cutting saw chain
  • Multifunction lever controls choke, throttle advance, run and stop modes
  • Extended drive sprocket adapter offers easy chain assembly
  • Deep cutting solution for obstructed or small openings
  • Easy-to-start in all weather

Engine

Engine Power 3.7 kW (5 hp) @ 9,500 rpm
Engine Torque 4.1 Nm (36.3 in-lbs) @ 6,500 rpm
Rated Engine Speed 11500 +/- 500 rpm (max) / 2,800 - 3,200 rpm (Idle)
Displacement 76.5 cc (4.7 cu-in)
Engine Type 2-stroke
Cooling Air Cooled
Starter Dust and water resistant
Ignition Special water resistant electronic ignition

Fuel Usage

Fuel Usage, 100% Load Fuel ratio: 4% (25:1) gasoline-to-oil

Operational

Hydraulic Flow Water Flow Requirement - Minimum: 4 lpm (1 gpm)
Maximum Pressure Water Supply Requirement - Minimum: 1.5 bar (20 psi)
Operating Speed Chain at Maximum Power: 34.5 m/s (6800 ft /min)
Operating Conditions Vibration, ahv eq Concrete Cutting (2): 7.2 m/s2 (K=1.0 m/s2) Front Handle/8.5 m/s2 (K=1.0 m/s2) Rear Handle

Performance

Noise Level Equivalent Sound Pressure at the Operator's Ear Lwa: 101.0 dB(A) (K = 2.0 dB(A)) | Guaranteed Sound Power Level, Lwa (1): 117 dB(A) (Kwa=3.0 dB(A))

Dimensions

Length 46 cm (18 in)
Height 29 cm (11.5 in)
Width 25 cm (10 in)

Capacities

Fuel Capacity 0.88 liter (0.23 gallon)

Weights

Weight 9.5 kg (21 lbs) powerhead only

Product Photography